Home

Technical Details Compression Springs

Production Capacity:

0,15 mm - 22,00 mm

Parameters of conical compression springs

Physical parameters

d (wire diameter): This parameter describes the diameter of wire used as material for spring.
S (shaft): This parameter describes the maximum diameter of spring shaft in industrial applications. Tolerance for this parameter is (+-)2%(indicative).
De (Larger External Diameter): External diameter at large end of the spring. Tolerance for this parameter is (+-)2%(indicative).
Ds (Smaller Internal Diameter): Internal diameter at small end of the spring. Tolerance for this parameter is (+-)2%(indicative)
H (hole): This is the minimum diameter of the hole in which spring can work. Tolerance for this parameter is (+-)2%(indicative).
Ln (Block): Maximal length of a spring after total blocking. For most conical springs this value equals double wire diameter. Tolerance for this parameter is (+-)2%(indicative).
L0 (free length): Free length of compression springs is measured in its uncompressed state after previous one time blocking. Tolerance for this parameter is (+-)2%(indicative).
R (spring rate): This parameter determines spring's resistance, while it is working. It is measured in 1 DaN/mm = 10 N/mm. Tolerance for this parameter is (+-)15%(indicative).
L1 & F1 (length at force F): Force F1 at length L1 can be calculated from equation : F1 = (L0-L1) * R. Equation derrived from previous for calculating L1 : L1 = L0 - F1/R.

Compression spring parameters

Physical parameters

d (wire diameter): This parameter describes the diameter of wire used as material for spring.
S (shaft): This parameter describes the maximum diameter of spring shaft in industrial applications. Tolerance for this parameter is (+-)2%(indicative).
Di (internal diameter): Internal diameter of a spring can be calculated by subtracting the doubled wire diameter from the external diameter of a spring. Tolerance for this parameter is (+-)2%(indicative).
De (external diameter): External diameter of a spring can be calculated by adding the doubled wire diameter to the internal diameter of a spring. Tolerance for this parameter is (+-)2%(indicative).
H (hole): This is the minimum diameter of the hole in which spring can work. Tolerance for this parameter is (+-)2%(indicative).
P (pitch): Average distance between two subsequent active coils of a spring. Tolerance for this parameter is (+-)2%(indicative).
Lc (block length): Maximal length of a spring after total blocking. This parameter is shown in the picture on right. Tolerance for this parameter is (+-)15%(indicative).
Ln (allowable length): The maximum permitted length of a spring after loading. If deflection is higher it may cause plastic deformation (the non-reversible change of shape in response to an applied force). For many springs danger of deformation do not exists. In this case Ln = Lc + Sa, where Sa is the sum of minimum permissible spaces between active coils.
L0 (free length): Free length of compression springs is measured in its uncompressed state after previous one time blocking. Tolerance for this parameter is (+-)2%(indicative).
Nr of coils: This is a total number of coils in a spring - in the picture above it is equal to six. To calculate number of active coils substract two terminating coils from total number of coils.
R (spring rate): This parameter determines spring's resistance, while it is working. It is measured in 1 DaN/mm = 10 N/mm. Tolerance for this parameter is (+-)15%(indicative).
L1 & F1 (length at force F): Force F1 at length L1 can be calculated from equation : F1 = (L0-L1) * R. Equation derrived from previous for calculating L1 : L1 = L0 - F1/R.
Grinding: Defines whether or not the ends of a spring are ground.

Characteristics

Ends: All compression springs have flat ends.
Spring rate: Tolerance for spring rate is (+-)15%(indicative).

Wire Types: :

music wire: a high carbon steel for high stress applications
harddrawn MB: a carbon steel for low stresses and low cost
oil tempered wire: a carbon steel for wire forms and torsion springs
stainless steel: types 302 and 316 for high stresses in larger wire sizes
chrome vanadium: an alloy wire for high stresses in larger wire sizes
phosphor bronze: for electrical applications
brass: for applications requiring water resistance
others: available on as needed basis

Telsama Metal Ith. Ihr. Dan. San. ve Tic. Ltd. Şti.
Minareli Cavus Mah. NOSAB Dokumculer Sitesi 103 Sokak No:48 Nilufer- 16150 Bursa, Turkiye
Tel:+90 224 411 1091 Fax:+90 224 411 1092

© Copyright TELSAMA GROUP OF COMPANIES | Tasarım ve Hosting Fononline(www.siteadi.com)

Paylaş